Moldes para fundição sob baixa pressão (LPDC)
Moldes para fundição por gravidade
Moldes de fundição por contrapressão (CPC)
Molde para fundição de peças estruturais
Molde de fundição para cubo de roda de motocicleta
Molde de fundição por pressão diferencial para cub
Molde para fundição por gravidade de cubos de roda
Baixa pressão no cubo da roda
The consistency of multiple cavities relies on three things: same machining of cavities, same batch heat treatment, and synchronous cooling.
1、 Same machining reduces benchmark deviation
The cavities of multi cavity aluminum alloy casting molds should be processed under the same equipment and clamping reference.
The machining of the machine will cause the positional deviation of the mold cavity to expand to more than 0.15 millimeters.
The number of cavities in a single mold set is often taken as 2 to 4 cavities, and the difficulty of controlling consistency increases significantly beyond 4 cavities.
2、 Same batch heat treatment
It is recommended to heat treat the cavity inserts in the same furnace, with a hardness difference controlled within 1.5HRC.
Batch heat treatment can cause a difference of about 0.05 millimeters in the deformation of the mold cavity.
Unified precision machining after heat treatment can eliminate deviations caused by deformation.
3、 Synchronous cooling
Multiple cavities need to share the same waterway collector, and the flow deviation of each cavity should be controlled within 10%.
When the flow deviation exceeds 20%, the temperature difference between the cavity molds can reach 10 degrees Celsius, and the size will drift accordingly.
Xinfeng uses parallel equal path water circuits on multi cavity molds to reduce temperature differences between cavities.
4、 First article and batch validation
The first piece needs to be measured for full size cavity by cavity, and the deviation between cavities should be controlled within 0.15 millimeters.
Randomly inspect one piece every 200 pieces in batch, and rotate the sampling by cavity to avoid omissions.
When the deviation between cavities exceeds 0.2 millimeters, the machine should be stopped to check the position of the embedded block.
5、 Balance between production capacity and cost
The single piece cost of multi cavity molds is about 20% to 30% lower, but the mold investment is about 50% higher.
When the annual demand is less than 30000 pieces, the amortization advantage of multi cavity molds is not significant.
Industry data shows that dual cavity molds that meet consistency standards have better comprehensive benefits than four cavity molds.
Conclusion and Outlook
The value of multiple cavities lies in efficiency, while the risk lies in consistency.
Only by implementing the same machining, same batch heat treatment, and synchronous cooling can the deviation between cavities be stabilized.
Extension: Three key points for using multi cavity molds
Key point one: When replacing the inlay block, the entire set must be replaced, and single cavity replacement will introduce new deviations.
Key point 2: The top pins of each cavity need to be maintained synchronously, as single cavity jamming can cause deviation to widen.
Key point three: Perform multi cavity sampling in rotation to avoid long-term testing of only the same cavity.
When the three key points are ignored, the inter cavity deviation often expands to 0.25 millimeters within three months.
Xinfeng attaches cavity number markings on multi cavity molds for easy recording of each cavity.
After filing according to the cavity, the deviation trend is easier to grasp.
Addendum: Four management practices for multi cavity molds
The water collector needs to be equipped with a flow meter, and checking each chamber is more reliable than adjusting it by hand.
The positioning of the inlay block adopts a unified reference hole, and there is no need to recalibrate when changing the cavity.
Measure the full size of the first piece cavity by cavity and record the cavity number, in order to track the deviation trend.
After the inter cavity deviation stabilizes within 0.15 millimeters, the sampling frequency will be relaxed.
Addendum 2: Three cost accounts for multi cavity molds
The investment in multi cavity molds is about 50% higher than that of single cavity molds, and the cost per piece is about 20% to 30% lower.
After increasing the number of cavities, the maintenance time increases synchronously, with each maintenance lasting about 1 hour longer.
When the annual demand is less than 30000 pieces, the economy of multi cavity is usually not significant.
FAQ
How many cavities are suitable for the number of cavities? Usually 2 to 4 chambers.
How much is the inter cavity deviation controlled? Suggest within 0.15 millimeters.
What is the difference in hardness control? The same furnace heat treatment can be controlled within 1.5HRC.
What is the appropriate amount of traffic deviation? Control within 10%.
How much cost does a multi cavity mold save? A single item is about 20% to 30% lower.
How much annual demand is cost-effective? Usually over 30000 pieces.
Should the first piece be tested cavity by cavity? Need to avoid missing deviations.
Hot spots on spokes of wheel hub molds: causes and three countermeasures
Moldes para fundição por baixa pressão (LPDC)
Moldes para fundição por gravidade
Moldes para fundição por contrapressão (CPC)
Moldes para fundição de peças estruturais
Molde para fundição de cubos de roda de motocicleta
Molde para fundição por pressão diferencial de cubos de roda
Molde para fundição por gravidade de cubos de roda
Molde para fundição por baixa pressão de cubos de roda
MOLDES PARA JANTES AUTOMÓVEIS
PEÇAS ESTRUTURAIS AUTOMÓVEIS
OUTROS COMPONENTES DE FUNDIDOS DE ALUMÍNIO
PERFIL DA EMPRESA
ESTRUTURA ORGANIZACIONAL
HISTÓRICO DE DESENVOLVIMENTO
PROPRIEDADE INTELECTUAL
ESPÍRITO DE EQUIPA PARCEIRO
Copyright © Zhejiang Xinfeng Machinery Co., Ltd. All Rights Reserved.