Moldes para fundição sob baixa pressão (LPDC)
Moldes para fundição por gravidade
Moldes de fundição por contrapressão (CPC)
Molde para fundição de peças estruturais
Molde de fundição para cubo de roda de motocicleta
Molde de fundição por pressão diferencial para cub
Molde para fundição por gravidade de cubos de roda
Baixa pressão no cubo da roda
Dimensional tolerances and testing standards for aluminum alloy castings: how to determine acceptance
The acceptance criteria should be quantifiable: size tolerance classification, flaw detection level, and sampling frequency should be clearly stated.
1、 Dimensional tolerance classification
The tolerance for key installation surfaces is set at 0.15 to 0.2 millimeters, while for general surfaces it is set at 0.3 to 0.5 millimeters.
The wall thickness tolerance is usually controlled at plus or minus 0.5 millimeters, and thin-walled parts are tightened to plus or minus 0.3 millimeters.
Tight tolerances can significantly increase mold costs, typically by about 8% for every 0.05 millimeters of tightening.
2、 Testing grade
General parts shall be inspected at level 2, while safety parts shall be inspected at level 1 or level 2 with stricter inspection.
The defect area limit in the critical stress zone is set at 3 square millimeters.
The detection method should specify whether it is X-ray, CT or penetration, and the differences in conclusions between different methods are significant.
3、 Sampling frequency
First article full inspection, with one sample checked every 200 to 500 pieces during the batch stage.
After three consecutive batches of qualified products, the frequency can be relaxed, and if there are abnormalities, it will immediately return to full inspection.
Contracts with unspecified sampling ratios have a significantly higher probability of acceptance disputes.
4、 Judgment and disposal
Unqualified batches need to be isolated and traced back to the mold number and process parameters.
The repaired parts need to be re inspected, and polishing should not be used as a substitute for testing.
Concession acceptance requires written confirmation and a limited scope of use.
5、 Documents and Foreign Trade
The delivery documents include a three coordinate report, inspection records, and material certification.
European customers require additional reports on material composition and mechanical properties.
Xinfeng listed tolerance grading and testing methods in the acceptance checklist to reduce caliber differences.
Conclusion and Outlook
The ambiguity of standards is the root cause of acceptance disputes, and quantifying terms can save a lot of communication costs.
Clearly state the tolerance grading, flaw detection method, and sampling frequency, and improve the pass rate of acceptance once.
Extension: Three time costs in the detection process
Three coordinate full-size inspection of a single piece takes about 1 to 2 hours, and batch sampling needs to be scheduled for production.
X-ray inspection of a single item takes about 10 to 20 minutes, and complex items require multi angle photography.
Penetration testing requires waiting for imaging, which takes about 30 minutes per test.
Three time costs have not been included in the plan, and delivery is often delayed by 2 to 4 days.
Include testing hours in the project schedule for a more reliable delivery commitment.
When the detection capability is insufficient, it is recommended to outsource in advance and lock in the schedule.
Addendum: Five supplementary explanations for the acceptance criteria
The tolerance zone needs to consider mold wear, and the size of the batch will drift by about 0.1 millimeters in the later stage.
The testing standard should indicate the testing surface and angle, and the conclusions may be opposite for different angles.
The sampling frequency is linked to the output, and it is recommended to sample one piece every 500 pieces for an annual output of 100000 pieces.
Concession acceptance should be limited to batches and quantities to avoid default conventions.
The inspection report should include the equipment number and operator, and the traceability chain should be more complete.
Addendum 2: Three Practices for Standard Communication
Before mold opening, it is crucial to confirm the inspection checklist with the customer, as both parties have a consistent understanding of the project quantity.
It is recommended to attach a schematic diagram for the judgment criteria, as a purely textual description can easily lead to ambiguity.
Freeze the shipment first when there are batch abnormalities, and resume it after the re inspection conclusion is clear.
Addendum 3: Two rules for re inspection and release
Unqualified batches can only be released after passing the re inspection, and personnel and equipment need to be replaced for re inspection.
Two consecutive batches of unqualified products need to be stopped for analysis, and continuing production will amplify losses.
FAQ
What is the tolerance for critical surfaces? 0.15 to 0.2 millimeters.
How to control the wall thickness tolerance? Usually plus or minus 0.5 millimeters, thin-walled parts plus or minus 0.3 millimeters.
How much does the cost of tightening tolerances increase? Approximately 8% increase for every 0.05 millimeters.
How to determine the level of flaw detection? Universal Level 2, Safety Component Level 1.
What is the limit for defect area? The key area has a permanent area of 3 square millimeters.
What is the sampling frequency? Every 200 to 500 pieces.
Do the repaired parts need to be re inspected? Re inspection is required and cannot be replaced by grinding.
Multi cavity aluminum alloy casting mold: how to control consistency within 0.15 millimeters
Moldes para fundição por baixa pressão (LPDC)
Moldes para fundição por gravidade
Moldes para fundição por contrapressão (CPC)
Moldes para fundição de peças estruturais
Molde para fundição de cubos de roda de motocicleta
Molde para fundição por pressão diferencial de cubos de roda
Molde para fundição por gravidade de cubos de roda
Molde para fundição por baixa pressão de cubos de roda
MOLDES PARA JANTES AUTOMÓVEIS
PEÇAS ESTRUTURAIS AUTOMÓVEIS
OUTROS COMPONENTES DE FUNDIDOS DE ALUMÍNIO
PERFIL DA EMPRESA
ESTRUTURA ORGANIZACIONAL
HISTÓRICO DE DESENVOLVIMENTO
PROPRIEDADE INTELECTUAL
ESPÍRITO DE EQUIPA PARCEIRO
Copyright © Zhejiang Xinfeng Machinery Co., Ltd. All Rights Reserved.