Perguntas frequentes

The thermal load of the mold and the defect rate of the casting change synchronously for every 10 degrees Celsius deviation in the temperature of the aluminum l

  • Vistas: ...
  • Tempo de liberação: 2026-11-16

The thermal load of the mold and the defect rate of the casting change synchronously for every 10 degrees Celsius deviation in the temperature of the aluminum liquid.

1、 Temperature Window

The pouring temperature of aluminum alloy is usually between 690 and 720 degrees Celsius, with a lower limit for thin-walled parts and an upper limit for thick walled parts.

When the temperature exceeds 730 degrees Celsius, the air intake increases by about 15% and the porosity increases.

When the temperature is below 680 degrees Celsius, the probability of insufficient filling and cold insulation increases by about 25%.

2、 Thermal shock to molds

For every 10 degrees Celsius increase in the temperature of the aluminum liquid, the thermal shock stress on the mold surface increases by about 8%.

Under long-term high-temperature conditions, the occurrence time of thermal fatigue cracks in the mold cavity is about 20% earlier.

The surface coating can cushion thermal shock, but it cannot replace temperature control.

3、 Coordination with mold temperature

When the mold temperature is low, it is necessary to increase the pouring temperature compensation, but it will exacerbate the thermal shock and form a vicious cycle.

The mold temperature in the thin-walled area is set at 300 to 330 degrees Celsius, which can reduce the dependence on high-temperature aluminum liquid.

After the mold temperature stabilizes, the fluctuation of pouring temperature should be narrowed to plus or minus 5 degrees Celsius.

4、 Temperature measurement and recording

It is recommended to measure the temperature of the aluminum liquid once per furnace using an immersion thermocouple.

When the temperature control deviation of the insulation furnace exceeds 10 degrees Celsius, the thermocouple should be calibrated.

Xinfeng listed the matching range between the aluminum liquid temperature and the mold temperature in the process proposal.

5、 Defect association

High pouring temperature is often accompanied by gas entrapment and oxidation inclusions, resulting in a decrease in the pass rate of non-destructive testing.

If the temperature is too low, cold insulation and undercasting will occur, and the proportion of appearance repairs will increase.

Industry data shows that narrowing the temperature window by 10 degrees Celsius can reduce the scrap rate by about 12%.

Conclusion and Outlook

The temperature of aluminum liquid is a common switch between mold life and casting quality.

Fix the temperature window, mold temperature matching, and temperature measurement record, and the fluctuations will naturally converge.

Extension: Three measured details of aluminum liquid temperature

Immersion thermocouples require preheating, and direct insertion may result in a reading deviation of 2 to 5 degrees Celsius.

The temperature measurement point should be at least 150 millimeters below the liquid level, and the reading near the furnace wall should be higher.

The temperature difference between the insulation furnace and the transfer bag often reaches 8 degrees Celsius, and they need to be measured separately.

Only by achieving three details can temperature records be comparable.

Xinfeng listed the temperature measurement points and frequency requirements in the process proposal.

The temperature ledger is reviewed monthly, making it easier to detect parameter drift.

Addendum: Four Precautions in Temperature Management

The temperature drop during transportation often reaches 15 degrees Celsius, and the temperature needs to be rechecked before pouring.

When the liquid level of the insulation furnace is low, the temperature fluctuation is greater. It is recommended to keep it above 70%.

If the aluminum liquid is left to stand for more than 30 minutes, it needs to be re measured, otherwise the reading will be distorted.

Comparing temperature records with defect types makes it easier to detect abnormal patterns.

Addendum 2: Correspondence between Defects and Temperature

Curling defects often occur in combinations of high temperature and rapid filling.

Cold insulation defects often occur in situations where the temperature is too low or the mold temperature is insufficient.

Shrinkage is concentrated in the thick walled area and is directly related to the holding time and temperature gradient.

FAQ

What is the pouring temperature? Usually between 690 and 720 degrees Celsius.

What will happen if the temperature is too high? The inhalation volume increases by about 15%, and the porosity increases.

What will happen if the temperature is too low? The probability of cold insulation and undercasting increases by about 25%.

How much does the stress increase per liter at 10 degrees Celsius? About 8%.

How often should the temperature of the aluminum liquid be measured? Suggest once per furnace.

What is the appropriate temperature for the mold? Thin walled area at 300 to 330 degrees Celsius.

How much waste can be reduced by narrowing the temperature control window? About 12%.

Release agent and cavity surface: dosage, concentration, and carbon deposition control

Sítio Web Deste artigo: https://pt.zj-xinfeng.com/case/1503.html

Get a Custom Product Proposal Online

Please fill out the form below to receive this for free.

Global Hotline:

+86-15356852630,13967513266

Moldes para fundição por baixa pressão (LPDC) 
Moldes para fundição por gravidade 
Moldes para fundição por contrapressão (CPC) 
Moldes para fundição de peças estruturais
Molde para fundição de cubos de roda de motocicleta
Molde para fundição por pressão diferencial de cubos de roda
Molde para fundição por gravidade de cubos de roda
Molde para fundição por baixa pressão de cubos de roda

MOLDES PARA JANTES AUTOMÓVEIS 
PEÇAS ESTRUTURAIS AUTOMÓVEIS 
OUTROS COMPONENTES DE FUNDIDOS DE ALUMÍNIO

NOTÍCIAS DA EMPRESA
NOTÍCIAS DO SETOR
BLOG TÉCNICO
PERGUNTAS FREQUENTES

PERFIL DA EMPRESA
ESTRUTURA ORGANIZACIONAL
HISTÓRICO DE DESENVOLVIMENTO
PROPRIEDADE INTELECTUAL
ESPÍRITO DE EQUIPA PARCEIRO

Copyright © Zhejiang Xinfeng Machinery Co., Ltd. All Rights Reserved.