Perguntas frequentes

Common misconceptions about exhaust ducts include opening in the wrong position, improper depth, insufficient area, only opening without maintenance, and neglec

  • Vistas: ...
  • Tempo de liberação: 2026-11-16

Common misconceptions about exhaust ducts include opening in the wrong position, improper depth, insufficient area, only opening without maintenance, and neglecting the joint of the embedded block.

1、 Location is more important than quantity

The exhaust groove should be opened in the last filling area of the aluminum liquid, and it is almost ineffective to open it in the early filling area.

When the position is correct, the porosity can decrease by about 40%, and no amount can be replenished.

Using CAE final filling diagram for positioning is more reliable than relying on experience for slotting.

2、 Depth depends on the process

The exhaust groove depth for gravity casting molds is 0.2 to 0.3 millimeters, and for low-pressure molds it is 0.15 to 0.2 millimeters.

The CPC reverse pressure casting mold is shallower, ranging from 0.10 to 0.15 millimeters, while also ensuring sealing.

If the depth exceeds 0.3 millimeters, it is easy to run aluminum, and if it is below 0.1 millimeters, the exhaust is not smooth.

3、 The area should be calculated based on projection

The total cross-sectional area of the exhaust groove shall not be less than 8 square millimeters per 100 square centimeters based on the projected area of the cavity.

Thin walled parts and fast filling processes need to float up to 10 to 12 square millimeters.

When the area is insufficient, the probability of under casting at the end increases by about 25%.

4、 The gap between the inlay seam and the top needle should be included in the calculation

The inlay seam is 0.05 to 0.10 millimeters, and the top needle gap is 0.03 to 0.05 millimeters, both of which can be used as auxiliary exhaust.

Neglecting these two exhausts will increase the porosity of the deep cavity components to over 3%.

Xinfeng listed the inspection items for the insert and ejector pin exhaust in the mold acceptance checklist.

5、 Only opening without maintenance is equivalent to not opening

If the carbon deposition thickness in the exhaust groove exceeds 0.05 millimeters, the exhaust efficiency will decrease by about half.

It is recommended to clean the exhaust groove every 500 molds using specialized cleaning blades.

Industry practice has shown that after standardizing exhaust maintenance, the repair rate of air holes can be reduced by about 30%.

Conclusion and Outlook

Exhaust is a low-cost defect control method, but it requires data to support the location and size.

By positioning according to the final filling diagram, determining the depth according to the process, and determining the area according to the projection, all three measures will be effective.

Extension: Three Practical Methods for Exhaust Verification

Observe the gas flow direction through smoke emission or low-pressure testing to determine if the exhaust is unobstructed.

After the mold is closed, the ventilation test shows that if the exhaust flow rate is lower than the set value, the groove depth needs to be repaired.

Batch X-ray spot checks are conducted, and if the air holes are concentrated in the same area, it indicates insufficient exhaust.

After cleaning the carbon deposits in the exhaust groove, the porosity should decrease. If there is no change, it indicates that the position has been selected incorrectly.

When none of the three measurements match, it is necessary to return to the CAE final filling diagram and reposition.

Record the actual measurements in the mold file, and the conclusions can be directly reused for subsequent modifications.

Addendum: Three precautions for exhaust groove processing

A 0.5mm transition should be left between the exhaust groove and the edge of the mold cavity, as direct passage may cause edge breakage.

Multi cavity molds should be equipped with exhaust slots for each cavity, and sharing one exhaust channel can lead to uneven flow in each cavity.

After processing, it is necessary to thoroughly remove burrs, which will reduce the effective depth by about 0.03 millimeters.

Addendum 2: Two judgments on exhaust effect

Two consecutive batches of air holes in the same area indicate that the exhaust at that location is insufficient and needs to be re slotted.

After cleaning the exhaust groove, the porosity did not decrease, usually due to incorrect positioning rather than depth issues.

FAQ

Where is the exhaust duct located? The final filling position of aluminum liquid.

How deep is the exhaust groove of the gravity mold? 0.2 to 0.3 millimeters.

How deep is the exhaust groove of CPC mold? 0.10 to 0.15 millimeters.

How is the exhaust area calculated? The projection shall not be less than 8 square millimeters per 100 square centimeters.

Is the block seam considered as exhaust? Calculate, 0.05 to 0.10 millimeters can assist with exhaust.

How often should it be cleaned? Suggest once every 500 cycles.

How thick is carbon deposition affecting exhaust? Efficiency is halved when it exceeds 0.05 millimeters.

Aluminum alloy casting mold steel and heat treatment: how to determine the hardness range

Sítio Web Deste artigo: https://pt.zj-xinfeng.com/case/1483.html

Get a Custom Product Proposal Online

Please fill out the form below to receive this for free.

Global Hotline:

+86-15356852630,13967513266

Moldes para fundição por baixa pressão (LPDC) 
Moldes para fundição por gravidade 
Moldes para fundição por contrapressão (CPC) 
Moldes para fundição de peças estruturais
Molde para fundição de cubos de roda de motocicleta
Molde para fundição por pressão diferencial de cubos de roda
Molde para fundição por gravidade de cubos de roda
Molde para fundição por baixa pressão de cubos de roda

MOLDES PARA JANTES AUTOMÓVEIS 
PEÇAS ESTRUTURAIS AUTOMÓVEIS 
OUTROS COMPONENTES DE FUNDIDOS DE ALUMÍNIO

NOTÍCIAS DA EMPRESA
NOTÍCIAS DO SETOR
BLOG TÉCNICO
PERGUNTAS FREQUENTES

PERFIL DA EMPRESA
ESTRUTURA ORGANIZACIONAL
HISTÓRICO DE DESENVOLVIMENTO
PROPRIEDADE INTELECTUAL
ESPÍRITO DE EQUIPA PARCEIRO

Copyright © Zhejiang Xinfeng Machinery Co., Ltd. All Rights Reserved.