Moldes para fundição sob baixa pressão (LPDC)
Moldes para fundição por gravidade
Moldes de fundição por contrapressão (CPC)
Molde para fundição de peças estruturais
Molde de fundição para cubo de roda de motocicleta
Molde de fundição por pressão diferencial para cub
Molde para fundição por gravidade de cubos de roda
Baixa pressão no cubo da roda
The steering knuckle is a safety component, and the core red line of the mold is the internal density, dimensional tolerance, and traceability record.
1、 Prioritizing density over appearance
The primary goal of steering joint mold design is to eliminate internal shrinkage holes, and the inspection level is usually required to be at least level two.
The defect area in the critical stress zone must be less than 3 square millimeters, otherwise it will be judged as unqualified.
When using LPDC process, the holding pressure is set at 0.8 to 1.0 bar, resulting in a density increase of about 15%.
2、 Dimensional tolerance is calculated in reverse according to the loading chain
The flatness of the installation surface of the steering knuckle and brake caliper is usually controlled within 0.15 millimeters.
Tightening the tolerance of the pin hole position to 0.2 millimeters can reduce the drift of the four-wheel alignment parameters by about 20%.
If the wear of the mold cavity of the steering joint exceeds 0.3 millimeters, the mold needs to be repaired, otherwise the batch size will drift.
3、 Traceability and Batch Management
The safety components require single piece traceability, and the mold must be equipped with a mold counter and batch identification.
At least 3 samples should be retained for each batch, with a retention period of no less than two years, to facilitate quality traceability.
Xinfeng has installed a mold count and temperature recording interface on the steering knuckle mold to facilitate customer documentation.
4、 Process selection and batch matching
If the annual demand is less than 30000 pieces, gravity casting can be considered, with a cost reduction of about 30%, but the density is slightly lower.
If the annual demand exceeds 50000 pieces, it is recommended to use low-pressure casting molds to ensure better rhythm and consistency.
The CPC process is suitable for high safety level projects, with an investment of about 1.6 times higher and a scrap rate of up to 1.2%.
5、 Foreign Trade Compliance Reminder
Exporting to Europe requires providing material composition and mechanical performance reports that comply with local standards.
North American customers often require PPAP document packages, and testing hours should be reserved during the mold development phase.
The contract should specify the testing standards and judgment methods to avoid disputes during the acceptance stage.
Conclusion and Outlook
The value of safety component molds lies in stability, not in the high or low cost of individual pieces.
By placing the three red lines of density, tolerance, and traceability in the design phase, the batch production complaint rate can be reduced by about 30%.
Extension: Checklist for Safety Component Procurement
Verify the testing methods and criteria, and the differences in conclusions can reach up to one level depending on the method used.
Verify the degassing records of aluminum liquid, and the risk increases significantly when the gas content exceeds 0.2 milliliters per 100 grams.
Check the mold material and heat treatment curve. If the hardness deviation exceeds 3HRC, the batch needs to be traced.
Verify the trial mold curve and process parameters. Missing parameters will prolong the mass production validation by about two weeks.
Verify the rules for repair and concession acceptance to avoid using polishing as a substitute for non-destructive testing.
For projects with a complete list of five items, the first round acceptance rate is usually about 20% higher.
Addendum: Three practical suggestions for steering joint molds
The position of the sprue should avoid the stressed rod, as grinding the residual roots of the sprue too deeply will weaken the cross-sectional strength.
It is recommended to perform both slicing and X-ray at the same time for the first article. The two methods complement each other, and a single method may easily miss the detection of internal shrinkage.
When defects occur in two consecutive batches at the same location, priority should be given to reviewing the mold temperature and holding pressure curves, rather than directly repairing the mold.
FAQ
What are the requirements for inspection of steering knuckles? Usually at level two or above, critical area defects are less than 3 square millimeters.
What is the flatness tolerance? The installation surface is usually controlled within 0.15 millimeters.
How much cavity wear does it require mold repair? If it exceeds 0.3 millimeters, the mold needs to be repaired.
What is the annual output for choosing LPDC? It is recommended to use low-pressure casting molds for over 50000 pieces.
How long should the sample be kept for? Not less than two years, at least three pieces per batch.
What documents are required for exporting to Europe? Material composition and mechanical performance report.
What should be stated in the contract? Testing standards and judgment methods.
Control arm mold: deformation control method for thin-walled aluminum parts
Moldes para fundição por baixa pressão (LPDC)
Moldes para fundição por gravidade
Moldes para fundição por contrapressão (CPC)
Moldes para fundição de peças estruturais
Molde para fundição de cubos de roda de motocicleta
Molde para fundição por pressão diferencial de cubos de roda
Molde para fundição por gravidade de cubos de roda
Molde para fundição por baixa pressão de cubos de roda
MOLDES PARA JANTES AUTOMÓVEIS
PEÇAS ESTRUTURAIS AUTOMÓVEIS
OUTROS COMPONENTES DE FUNDIDOS DE ALUMÍNIO
PERFIL DA EMPRESA
ESTRUTURA ORGANIZACIONAL
HISTÓRICO DE DESENVOLVIMENTO
PROPRIEDADE INTELECTUAL
ESPÍRITO DE EQUIPA PARCEIRO
Copyright © Zhejiang Xinfeng Machinery Co., Ltd. All Rights Reserved.