Perguntas frequentes

Casting molds for automotive structural components: five key selection points for new energy lightweight projects

  • Vistas: ...
  • Tempo de liberação: 2026-11-16

Casting molds for automotive structural components: five key selection points for new energy lightweight projects

Key points of structural component molds: After thinning the wall thickness, the rigidity, cooling, and tolerance of the mold must be upgraded synchronously.

1、 Stiffness precedes accuracy

The wall thickness of the mold cavity for automobile structural component casting is usually 15% to 20% thicker than that of general molds, which suppresses deformation.

The weight of a single new energy subframe is about 8 to 12 kilograms, and the filling pressure is high. Insufficient stiffness in the mold cavity can lead to wall thickness deviation.

For every 0.1 millimeter increase in deformation of the mold cavity, the clearance chain during loading will deteriorate and needs to be rechecked.

2、 Cooling structure is divided into zones according to wall thickness

The spacing between water channels in thin-walled areas is set at 20 to 25 millimeters, while in thick walled areas it is set at 30 to 35 millimeters, forming a gradient cooling.

Uneven cooling can cause a hardness difference of more than 20HB on the same piece, resulting in tool failure during subsequent machining.

Xinfeng's structural component molds adopt zone independent temperature control, which can shorten the single piece cycle time by about 12%.

3、 Tolerance and allowance

The blank allowance for structural components is usually taken as 1.5 to 2.5 millimeters, which increases the machining time by about 10% if it is too large.

Tightening the tolerance of the key installation face to within 0.2 millimeters can increase the first pass rate of loading by about 18%.

The wall thickness tolerance is controlled at plus or minus 0.5 millimeters, and exceeding it will trigger a vehicle collision simulation review.

4、 Validation and Batch Production Transition

The first piece needs to undergo X-ray inspection and three-dimensional full-size testing, with porosity controlled within 2% before release.

During the small batch stage of 300 pieces, random inspections will be conducted once a week, and once stabilized, it can be relaxed to once every 500 pieces.

Industry reports show that the average number of mold trials for pre CAE structural components has decreased by about 1.5 times.

5、 Looking at demand from the perspective of foreign trade

Mexico and Vietnam have taken over the production capacity of new energy components, and inquiries for structural component molds have increased significantly in the past two years.

European customers are more concerned about material grades and inspection reports, while Southeast Asian customers are more concerned about delivery cycles and prices.

The plan with a complete simulation report has a 20% higher first round pass rate for overseas customers.

Conclusion and Outlook

The difficulty of structural component molds lies not in the cavity itself, but in the thermal balance problem caused by changes in wall thickness.

First, simulate the cooling process, then lock the tolerance and margin. The ramp up period for mass production can usually be shortened by three weeks.

Extension: Five Hidden Costs in Structural Component Projects

The repeated mold repair caused by insufficient cavity stiffness often accounts for more than 15% of the total development cost.

The rework of hot spots caused by improper cold design requires 7 to 10 days for a single rectification.

Uneven distribution of surplus caused machining to yield, resulting in an increase of about 8 percentage points in scrap rate.

If the inspection items are missed, the cost of retesting after batch production can be doubled.

The modification did not reserve a space for embedded blocks, and the secondary development cost is close to 30% of the new mold.

List the five costs item by item during the quotation stage, and the customer decision-making cycle is usually shortened by about one week.

Addendum: Three on-site experiences of structural component molds

The mold cavity of structural components is often assembled with embedded blocks, and the number of embedded blocks should be controlled within 4 to reduce joint deviation.

When the porosity of the first piece falls between 2% and 3%, the holding time is usually adjusted first rather than directly replacing the steel.

During the batch stage, the composition of waste products is counted weekly, and the proportion of porosity and deformation can best reflect the current state of the mold.

FAQ

How much is the wall thickness of the structural component mold cavity increased? Thicker than conventional molds by 15% to 20%.

What is the appropriate amount of blank allowance? Usually 1.5 to 2.5 millimeters.

How to control the wall thickness tolerance? Tighten the key surface to 0.2 millimeters by plus or minus 0.5 millimeters.

What testing is required for the first piece? X-ray inspection and three-dimensional full-size.

What is the porosity release line? Control within 2%.

What do overseas customers value the most? Europe looks at materials and testing, Southeast Asia looks at delivery time and price.

How many trial runs can simulation save? The average reduction is about 1.5 times.

Steering joint mold: Three red lines for casting safety components

Sítio Web Deste artigo: https://pt.zj-xinfeng.com/case/1471.html

Get a Custom Product Proposal Online

Please fill out the form below to receive this for free.

Global Hotline:

+86-15356852630,13967513266

Moldes para fundição por baixa pressão (LPDC) 
Moldes para fundição por gravidade 
Moldes para fundição por contrapressão (CPC) 
Moldes para fundição de peças estruturais
Molde para fundição de cubos de roda de motocicleta
Molde para fundição por pressão diferencial de cubos de roda
Molde para fundição por gravidade de cubos de roda
Molde para fundição por baixa pressão de cubos de roda

MOLDES PARA JANTES AUTOMÓVEIS 
PEÇAS ESTRUTURAIS AUTOMÓVEIS 
OUTROS COMPONENTES DE FUNDIDOS DE ALUMÍNIO

NOTÍCIAS DA EMPRESA
NOTÍCIAS DO SETOR
BLOG TÉCNICO
PERGUNTAS FREQUENTES

PERFIL DA EMPRESA
ESTRUTURA ORGANIZACIONAL
HISTÓRICO DE DESENVOLVIMENTO
PROPRIEDADE INTELECTUAL
ESPÍRITO DE EQUIPA PARCEIRO

Copyright © Zhejiang Xinfeng Machinery Co., Ltd. All Rights Reserved.