Perguntas frequentes

Casting molds for structural components of new energy vehicles: four changes brought about by lightweighting

  • Vistas: ...
  • Tempo de liberação: 2026-11-16

Casting molds for structural components of new energy vehicles: four changes brought about by lightweighting

Lightweight design enables structural component molds to move towards thin-walled, high-strength, and complex cavities, while simultaneously increasing cooling and tolerance requirements.

1、 Thinning of wall thickness

The wall thickness of new energy structural components often drops to 3 to 5 millimeters, and the filling time needs to be compressed to 0.10 to 0.18 seconds.

The cold insulation probability of thin-walled parts is about 25% higher than that of conventional parts, and mold temperature control is more critical.

When the speed of the sprue exceeds 3 meters per second, there is a significant increase in air entrainment.

2、 Material strength improvement

High strength aluminum alloy grades have a more significant impact on mold wear, and there is an increasing demand for wear-resistant treatment of the mold cavity.

The depth of the nitride layer is 0.02 to 0.05 millimeters, which can extend the lifespan of the cavity by about 15%.

The paint and release agent need to match the new brand to avoid sticking to the mold.

3、 The cavity is more complex

Integrated and integrated design increases the aspect ratio of the mold cavity, making it more difficult to exhaust and clean the cavity.

It is recommended to increase the spacing between the exhaust grooves in the deep cavity area to 15 to 20 millimeters.

The proportion of embedded block assembly has been increased, and the joint should be controlled within 0.05 to 0.10 millimeters.

4、 Tolerance and Inspection

Tighten the tolerance of the key installation surface to 0.15 to 0.2 millimeters, and tighten the assembly chain.

The porosity release line is mostly 2%, and the safety component is tightened to 1.2%.

Xinfeng packages simulation, point cooling, and detection solutions for new energy projects.

5、 Market and Capacity

The iteration of new energy vehicle models is fast, and the number of modifications during the mold life cycle increases.

By reserving replacement positions for embedded blocks based on platform design, the cost of retrofitting can be reduced by about 30%.

Industry observations show that inquiries for structural component molds are growing rapidly in Mexico and Southeast Asia.

Conclusion and Outlook

Lightweight is not just about reducing weight, but a comprehensive upgrade of mold heat and tolerance.

The three aspects of thin-walled filling, wear-resistant treatment, and deep cavity exhaust are firmly grasped, and the yield is significantly improved.

Extension: Three pre validations for lightweight projects

Perform simulation first for thin-walled filling verification, and then check if the end of the first piece is complete.

Wear resistance verification shows that the depth and hardness of the nitride layer are limited when the layer depth is less than 0.02 millimeters.

The deep cavity exhaust verification uses the smoke exhaust method, and if the end cannot exhaust gas, the exhaust groove needs to be encrypted.

The three verifications each take about 3 days, which can save one round of trial molding in total.

Write the verification conclusion into the process card, making it easier to locate anomalies during the batch stage.

Xinfeng issues first article reports based on three verifications in new energy projects.

Addendum: Four pre arrangements for lightweight projects

The modification frequency of new energy molds is usually once every 12 to 18 months, and there should be room for design.

Reserved replacement of embedded blocks can reduce modification costs by about 30%.

It is recommended to perform CT for the first thin-walled component, as internal defects are more difficult to detect than X-rays.

High strength aluminum grades have faster wear on the mold cavity, and the nitriding maintenance cycle needs to be shortened by about 20%.

Addendum 2: Three verifications for new energy vehicle projects

It is recommended to conduct collision simulation review for integrated structural components, as thinning the wall thickness will affect the stiffness.

It is recommended to conduct fatigue test sampling for the first article, and the number of cycles should be calculated according to the requirements of the entire vehicle.

During the batch stage, monitor size drift and repair molds if it exceeds 0.2 millimeters.

FAQ

What is the wall thickness of new energy structural components? Usually 3 to 5 millimeters.

What is the filling time? 0.10 to 0.18 seconds.

What is the probability of cold insulation for thin-walled components? About 25% higher than regular parts.

How much longer can nitriding extend its lifespan? About 15%.

What is the distance between deep cavity exhausts? Suggest 15 to 20 millimeters.

What is the porosity release line? Universal 2%, safety components 1.2%.

How can retrofitting save costs? Reserve replacement space for embedded blocks, reducing by about 30%.

Sítio Web Deste artigo: https://pt.zj-xinfeng.com/case/1499.html

Get a Custom Product Proposal Online

Please fill out the form below to receive this for free.

Global Hotline:

+86-15356852630,13967513266

Moldes para fundição por baixa pressão (LPDC) 
Moldes para fundição por gravidade 
Moldes para fundição por contrapressão (CPC) 
Moldes para fundição de peças estruturais
Molde para fundição de cubos de roda de motocicleta
Molde para fundição por pressão diferencial de cubos de roda
Molde para fundição por gravidade de cubos de roda
Molde para fundição por baixa pressão de cubos de roda

MOLDES PARA JANTES AUTOMÓVEIS 
PEÇAS ESTRUTURAIS AUTOMÓVEIS 
OUTROS COMPONENTES DE FUNDIDOS DE ALUMÍNIO

NOTÍCIAS DA EMPRESA
NOTÍCIAS DO SETOR
BLOG TÉCNICO
PERGUNTAS FREQUENTES

PERFIL DA EMPRESA
ESTRUTURA ORGANIZACIONAL
HISTÓRICO DE DESENVOLVIMENTO
PROPRIEDADE INTELECTUAL
ESPÍRITO DE EQUIPA PARCEIRO

Copyright © Zhejiang Xinfeng Machinery Co., Ltd. All Rights Reserved.