Moldes para fundição sob baixa pressão (LPDC)
Moldes para fundição por gravidade
Moldes de fundição por contrapressão (CPC)
Molde para fundição de peças estruturais
Molde de fundição para cubo de roda de motocicleta
Molde de fundição por pressão diferencial para cub
Molde para fundição por gravidade de cubos de roda
Baixa pressão no cubo da roda
CAE simulation can reduce the number of trial molds by one to two times, but it only solves the problems of filling and solidification and does not replace process validation.
1、 Three things to consider in charging simulation
A high-precision aluminum casting mold with CAE simulation first simulates the filling speed, coiling position, and final filling zone.
An exhaust groove should be added to the concentrated area of the rolled air, which can usually reduce the porosity by about 30%.
When the deviation between the filling time and the design value exceeds 15%, the gate section should be adjusted back.
2、 Solidification simulation with fixed compensation and shrinkage
The solidification simulation outputs the hot spot position and shrinkage probability, which are used to determine the riser and point cooling positions.
When the temperature gradient at the hot junction is below 5 degrees Celsius per centimeter, the risk of shrinkage significantly increases.
According to the simulation results, adding a riser can reduce the shrinkage area of the thick walled area to below 5%.
3、 Stress and deformation simulation
Mold thermal stress simulation can predict cavity deformation and crack risk, and guide the layout of cooling water channels.
When the peak deformation of the cavity exceeds 0.15 millimeters, the wall thickness and supporting structure need to be rechecked.
Xinfeng outputs thermal stress reports in high-precision projects to help customers predict mold repair nodes.
4、 The boundaries and limitations of simulation
The simulation relies on material parameters and boundary conditions, and the error of aluminum liquid heat transfer coefficient can reach 20%.
Simulation cannot replace measured model temperature, and the first piece still requires thermocouple and coordinate verification.
Factors such as coatings, release agents, and equipment fluctuations are often not fully covered by simulation models.
5、 Input-output ratio
Pre simulation increases development time by 5 to 7 days, resulting in an approximately 8% increase in development costs.
But the average number of trial molds is reduced by 1 to 2 times, and the cost of a single trial mold often accounts for 3% to 5% of the mold cost.
Industry practice shows that the comprehensive cost of simulating complex projects is actually about 6% lower.
Conclusion and Outlook
Simulation is moving trial and error from the workshop to the computer, reducing rework but not canceling validation.
For complex structural components, thin-walled components, and safety components, it is recommended to include simulation as a standard action.
Extension: How to view simulation results effectively
When the air roll is concentrated at the top of the mold cavity, an exhaust should be added instead of changing the sprue.
If the temperature gradient of the hot section is less than 5 degrees Celsius per centimeter, a riser or point cooling should be added.
If the filling time deviates from the design by more than 15%, first check the gate section and then check the injection parameters.
If the deformation exceeds 0.15 millimeters, priority should be given to reviewing the wall thickness and support, rather than encrypting the waterway.
When the simulation grid size is greater than 2 millimeters, the credibility of the detailed conclusions decreases.
According to these five criteria, the simulation report has the value of process guidance.
Addendum: Three prerequisites for simulation applications
The simulation model needs to be calibrated against the actual injection parameters, and the deviation of uncalibrated results often exceeds 20%.
It is recommended to use finer grids for thin-walled parts, and the conclusion of local flow state is only reliable when the size is less than 1 millimeter.
The simulation report should include a list of input parameters, as missing parameters can make it difficult to review the conclusions.
FAQ
What is CAE simulation mainly about? Filling, solidification, thermal stress and deformation.
How many trial molds can be reduced? Reduce by an average of 1 to 2 times.
How much does the simulation cost account for? The development cost has increased by approximately 8%.
Can simulation completely replace trial modeling? No, we still need to measure the mold temperature and coordinate system.
Which projects are recommended for simulation? Miscellaneous components, thin-walled components, and safety components.
What is the safe temperature gradient for a hot section? Suggest exceeding 5 degrees Celsius per centimeter.
What is the upper limit of cavity deformation? If it exceeds 0.15 millimeters, the structure needs to be reviewed.
Design of Cooling Water Channels for Aluminum Alloy Casting Molds: Quantification of Spacing, Flow Rate, and Temperature Difference
Moldes para fundição por baixa pressão (LPDC)
Moldes para fundição por gravidade
Moldes para fundição por contrapressão (CPC)
Moldes para fundição de peças estruturais
Molde para fundição de cubos de roda de motocicleta
Molde para fundição por pressão diferencial de cubos de roda
Molde para fundição por gravidade de cubos de roda
Molde para fundição por baixa pressão de cubos de roda
MOLDES PARA JANTES AUTOMÓVEIS
PEÇAS ESTRUTURAIS AUTOMÓVEIS
OUTROS COMPONENTES DE FUNDIDOS DE ALUMÍNIO
PERFIL DA EMPRESA
ESTRUTURA ORGANIZACIONAL
HISTÓRICO DE DESENVOLVIMENTO
PROPRIEDADE INTELECTUAL
ESPÍRITO DE EQUIPA PARCEIRO
Copyright © Zhejiang Xinfeng Machinery Co., Ltd. All Rights Reserved.