Perguntas frequentes

The key to achieving 50000 mold cycles for LPDC molds lies in the synergy of steel, heat treatment, cooling, and maintenance.

  • Vistas: ...
  • Tempo de liberação: 2026-11-16

The key to achieving 50000 mold cycles for LPDC molds lies in the synergy of steel, heat treatment, cooling, and maintenance.

1、 Steel and heat treatment are the foundation of lifespan

The mold cavity is made of hot work die steel containing more than 5% chromium, which has a thermal fatigue resistance about 40% higher than ordinary steel.

After quenching and tempering twice, the hardness is controlled at 48 to 52HRC, and the probability of early cracking in the mold cavity can be reduced by about 35%.

Hardness exceeding 55HRC is prone to edge breakage, and the crack propagation speed will increase by about 1.4 times.

2、 Cooling water channels determine thermal cycling stress

The distance between the waterway and the surface of the mold cavity is controlled at 25 to 35 millimeters, as being too close can lead to local supercooling and stress concentration.

For every 10 degrees Celsius decrease in mold surface temperature difference, the initiation time of thermal fatigue cracks can be delayed by about 20%.

The LPDC low-voltage casting mold with segmented temperature control can reduce the peak thermal stress of single mode by about 15%.

3、 The pressure curve affects the mold load

If the liquid lifting speed is too fast, the aluminum liquid will impact the mold cavity, and the depth of mold surface flushing will increase by about 0.05 millimeters per year.

The holding pressure increased from 0.6 bar to 0.9 bar, resulting in an increase in casting density, but the mold load also increased by about 12% simultaneously.

Set the curve according to the casting wall thickness classification, with thin-walled parts using low pressure slow rise and thick walled parts using high pressure short protection.

4、 Maintenance and ledger extension of actual lifespan

Performing cavity polishing and crack inspection every 5000 molds can extend the lifespan by approximately 10%.

Excessive spraying of release agent will accumulate carbon, and a carbon layer thicker than 0.1 millimeters in the mold cavity will affect heat dissipation.

The LPDC mold delivered by Xinfeng comes with a template for the mold number ledger, which records temperature and pressure curves on a weekly basis.

5、 Failure assessment and timing of mold replacement

If there are three or more consecutive hot cracks in the mold cavity, and the depth exceeds 1.5 millimeters, it enters the mold change window.

If the casting size drift exceeds 0.3 millimeters, it is mostly due to cavity creep, and the production yield will continue to drop below 90%.

Industry reports show that the average lifespan of standardized maintenance molds is about 25% higher than those without ledger management.

Conclusion and Outlook

The lifespan is not a single material indicator, but the product effect of steel, waterway, curve, and maintenance.

Requesting heat treatment records and waterway drawings during procurement can better determine the true lifespan than just looking at the quotation.

Extension: Five Misconceptions in Life Management

Only changing the steel without changing the waterway often results in a lifespan increase of less than 10%, and the investment and return are disproportionate.

Cases of line stoppage caused by edge breakage are not uncommon on mass production lines when the hardness reaches 56HRC or above.

Continuous production without mold temperature recording can result in thermal fatigue occurring up to 20% earlier.

After long-term circulation with untreated water and a scale thickness of 0.2 millimeters, the heat transfer efficiency significantly decreases and the beat slows down accordingly.

If the top pin is stuck without treatment, unilateral force will cause local cracking of the mold cavity, and the crack propagation speed will be about twice as fast.

Reviewing the ledger on a weekly basis and adjusting parameters, the actual lifespan is usually about 25% higher than that of molds without record management.

FAQ

What is the upper limit of the lifespan of LPDC molds? The standardized use can reach about 75000 cycles.

In which range is the hardness controlled? 48 to 52HRC, too high is prone to edge breakage.

How far is the appropriate distance between the waterway and the mold cavity? 25 to 35 millimeters, fine tuned according to the casting wall thickness.

How often do we have a cavity examination? Suggest once every 5000 cycles.

How deep does the crack require mold replacement? When the depth exceeds 1.5 millimeters and there are multiple consecutive strips, they should be replaced.

Is it better to increase the pressure? No, too high will increase the mold load and erosion.

How much lifespan can maintenance extend? Standardized maintenance is extended by approximately 10% to 25%.

Sítio Web Deste artigo: https://pt.zj-xinfeng.com/case/1468.html

Get a Custom Product Proposal Online

Please fill out the form below to receive this for free.

Global Hotline:

+86-15356852630,13967513266

Moldes para fundição por baixa pressão (LPDC) 
Moldes para fundição por gravidade 
Moldes para fundição por contrapressão (CPC) 
Moldes para fundição de peças estruturais
Molde para fundição de cubos de roda de motocicleta
Molde para fundição por pressão diferencial de cubos de roda
Molde para fundição por gravidade de cubos de roda
Molde para fundição por baixa pressão de cubos de roda

MOLDES PARA JANTES AUTOMÓVEIS 
PEÇAS ESTRUTURAIS AUTOMÓVEIS 
OUTROS COMPONENTES DE FUNDIDOS DE ALUMÍNIO

NOTÍCIAS DA EMPRESA
NOTÍCIAS DO SETOR
BLOG TÉCNICO
PERGUNTAS FREQUENTES

PERFIL DA EMPRESA
ESTRUTURA ORGANIZACIONAL
HISTÓRICO DE DESENVOLVIMENTO
PROPRIEDADE INTELECTUAL
ESPÍRITO DE EQUIPA PARCEIRO

Copyright © Zhejiang Xinfeng Machinery Co., Ltd. All Rights Reserved.