Moldes para fundição sob baixa pressão (LPDC)
Moldes para fundição por gravidade
Moldes de fundição por contrapressão (CPC)
Molde para fundição de peças estruturais
Molde de fundição para cubo de roda de motocicleta
Molde de fundição por pressão diferencial para cub
Molde para fundição por gravidade de cubos de roda
Baixa pressão no cubo da roda
Customization based on drawings involves five steps: drawing review, simulation verification, cavity processing, mold testing, and mass production release.
1、 Four things need to be clarified in drawing review
Before customizing aluminum alloy casting molds, it is necessary to confirm the aluminum liquid grade, annual output, testing standards, and machining allowance.
When the draft angle is missing in the drawing, it needs to be supplemented by 1 to 3 degrees, otherwise the probability of demolding strain will increase significantly.
For areas where the wall thickness suddenly changes by more than three times, it is necessary to confirm with the customer whether transition corners can be added.
2、 Simulation verification compression test times
Pre CAE can simulate filling and solidification, usually reducing 1 to 2 trial molds.
The simulation focuses on three aspects: the position of the rolled gas, the shrinkage area, and the solidification sequence.
Xinfeng provides filling and solidification simulation reports as attachments for drawing review in customized projects.
3、 Mold cavity processing and tolerance
The machining tolerance of the cavity is often taken as 0.02 millimeters, and the critical mating surface is taken as 0.01 millimeters.
Mold steel requires material certification and heat treatment hardness records to be delivered with the goods.
The surface roughness of the mold cavity is taken as Ra1.6 to Ra3.2, and excessive roughness will affect demolding.
4、 Trial molding and judgment
The first piece requires full-size measurement, X-ray and sectioning, with porosity controlled within 2%.
Trial molding is usually given 2 free opportunities, and any excess will be charged at approximately 3% of the mold fee per trial.
The trial mold record should retain temperature, pressure curves, and defect photos.
5、 Mass production release and foreign trade delivery
After three consecutive batches of qualified products, they can be released for mass production, and the frequency of batch inspections will gradually be relaxed.
Export orders need to be accompanied by three sets of material certificates, three coordinate reports, and trial mold records.
Industry practice shows that customized projects with sufficient drawing review have a repair rate that is about 30% lower.
Conclusion and Outlook
The risks of customizing molds are mostly in the front-end, not in the processing.
Clarifying the four inputs, pre simulation, and leaving traces of the trial model significantly improves delivery certainty.
Extension: Four essential documents in customized projects
The drawing review record should include confirmation of draft angle, shrinkage rate, and allowance.
The simulation report should include a diagram of the position of the rolled gas, distribution of hot nodes, and solidification sequence.
The heat treatment record should include the measured hardness value and tempering times.
The trial report should include temperature curve, pressure curve, and defect photos.
If any of the four documents are missing, the probability of disputes in the later stage will increase by about 30%.
Xinfeng archives these four documents in the customized project for the convenience of customer review and traceability.
Addendum: Three confirmations in the customization process
During the drawing review stage, it is necessary to confirm whether heat treatment processing is included. Different process sequences may cause changes in the allowance setting.
The first article inspection suggestion includes retesting of material composition, and any deviation in grade will significantly reduce the mechanical properties.
The requirement for modification is often raised after trial molding, and reserving the position of the insert can reduce the cost of secondary development by about 30%.
Addendum 2: Three explanations for customized quotation
The quotation should indicate whether it includes first article inspection and outsourced testing to avoid adding items temporarily during the acceptance stage.
The type of mold steel and heat treatment requirements need to be included in the quotation attachment, which is not easily replaceable in the later stage.
Delivery milestones are recommended to be listed on a weekly basis, and the customer's production schedule can be aligned with the mold progress.
FAQ
What information is required for customization? 3D drawings, production volume, testing standards, and aluminum liquid grades.
What should I do if there is a lack of draft angle? Set up at 1 to 3 degrees to avoid pulling.
How many trial runs can simulation save? Usually reduced by 1 to 2 times.
What is the tolerance for cavity machining? Usually take 0.02 millimeters and 0.01 millimeters for critical surfaces.
How many free trial runs? Normally, if exceeded twice, it will be calculated at approximately 3% of the mold cost.
Mass production release standards? Three consecutive batches of qualified, with porosity below 2%.
What documents are required for export? Material certification, three coordinate report, and trial mold record.
OEM LPDC wheel hub mold: delivery points for overseas foundry projects
Moldes para fundição por baixa pressão (LPDC)
Moldes para fundição por gravidade
Moldes para fundição por contrapressão (CPC)
Moldes para fundição de peças estruturais
Molde para fundição de cubos de roda de motocicleta
Molde para fundição por pressão diferencial de cubos de roda
Molde para fundição por gravidade de cubos de roda
Molde para fundição por baixa pressão de cubos de roda
MOLDES PARA JANTES AUTOMÓVEIS
PEÇAS ESTRUTURAIS AUTOMÓVEIS
OUTROS COMPONENTES DE FUNDIDOS DE ALUMÍNIO
PERFIL DA EMPRESA
ESTRUTURA ORGANIZACIONAL
HISTÓRICO DE DESENVOLVIMENTO
PROPRIEDADE INTELECTUAL
ESPÍRITO DE EQUIPA PARCEIRO
Copyright © Zhejiang Xinfeng Machinery Co., Ltd. All Rights Reserved.