Moldes para fundição sob baixa pressão (LPDC)
Moldes para fundição por gravidade
Moldes de fundição por contrapressão (CPC)
Molde para fundição de peças estruturais
Molde de fundição para cubo de roda de motocicleta
Molde de fundição por pressão diferencial para cub
Molde para fundição por gravidade de cubos de roda
Baixa pressão no cubo da roda
How to choose aluminum alloy casting molds: comparison of three types of processes: LPDC, gravity casting, and CPC
Selection depends on batch size and accuracy: LPDC is selected for monthly demand of over 3000 pieces, gravity is selected for 1000 pieces, and CPC is selected for high-end wheel hubs.
1、 Determine the process route based on batch scale
When the monthly demand exceeds 3000 pieces, the single piece amortization cost of LPDC low-voltage casting molds is about 18% lower than that of gravity molds.
The monthly demand is in the range of 500 to 1500 pieces, and the opening investment of gravity casting molds is about 32% lower, resulting in a shorter payback period.
CPC reverse pressure casting molds are suitable for high-end wheel hub projects with an annual output of over 100000 pieces, and the mold investment is about 1.6 times higher.
2、 Shape the cavity structure according to accuracy requirements
The porosity of CPC process castings can be compressed to below 0.8%, meeting the second level or above inspection and acceptance standards.
The porosity of LPDC castings is usually between 1.5% and 2.5%, suitable for conventional passenger car wheels and structural components.
The porosity of gravity cast parts is about 3%, and the defect rate needs to be controlled within 3% through the design of sprues and exhausts.
3、 Determine mold lifespan based on production conditions
A production line that operates continuously for three shifts should have a mold life of at least 50000 molds, otherwise significant losses will be incurred due to mold replacement and downtime.
A foundry with intermittent production can cover a usage cycle of about 18 months with 30000 molds, without the need for high demand.
When the chromium content of mold steel is higher than 5%, the occurrence time of thermal fatigue cracks can be delayed by about 30%.
4、 Determine suppliers based on delivery milestones
Overseas projects usually take 35 to 40 days from placing an order to the first trial mold, and exceeding 45 days will affect customer production scheduling.
Pre CAE simulation will take an additional 5 to 7 days, but the number of trial runs can be reduced by about 2, and the overall project schedule will not be delayed.
Xinfeng can provide three types of molds customized according to the drawings, with a cavity machining tolerance controlled within 0.02 millimeters.
Conclusion and Outlook
The three types of processes are not substitutes, and can only be finalized after the intersection of batch, precision, and working conditions.
First calculate the amortization of individual items, then verify the testing standards, and finally confirm the delivery milestones. The selection error rate can be reduced by about 40%.
In the past two years, orders from North America and Southeast Asia have leaned towards LPDC, while inquiries from high-end wheel projects in Europe to CPC have increased to 30%.
Extension: Three common types of misjudgments in selection
Treating quotations as a single criterion for judgment is a common misjudgment, and low-priced solutions often eliminate the need for full inspection of heat treatment, resulting in a higher cracking rate of about 35% in the later stage.
Using gravity molds to make high-end wheel hubs, the porosity is difficult to reach 0.8%, and the rework rate for non-destructive testing will increase by about 20%.
Blindly adopting CPC and insufficient production may result in a single piece amortization cost that is approximately 60% higher than LPDC.
Neglecting the differences in local aluminum liquid grades, a deviation of more than 0.5% in composition will cause the overall process parameters to be readjusted.
The unconfirmed interface and lifting point of the press machine resulted in an additional 3 to 5 days of debugging, which offset the advantage of delivery time.
Organize a process review before selection, including batch size, accuracy, and operating conditions in the conclusion, which can reduce the probability of misjudgment by about half.
Addendum: Three judgment criteria beyond quotation
Check whether the mold steel is accompanied by material certification and heat treatment curve. The solution for missing items usually saves the cost of testing and tempering.
Check if the cooling of the mold cavity is controlled independently by zones, and if the single zone is controlled on the wall thickness mixed discharge parts, the probability of hot spots is about 20% higher.
See if the supplier can provide trial mold curves and defect photos. Missing them will make it difficult for the customer to reproduce the production process during the mass production stage.
The comprehensive cost of a single item is usually about 8% lower with three complete solutions, as there are fewer rework and debugging hours.
FAQ
Which mold should I choose for producing 2000 wheels per month? LPDC is more suitable, with a single unit cost about 15% lower than gravity.
How much is CPC mold more expensive than LPDC? The same specification is approximately 1.5 to 1.8 times higher, depending on the level of non-destructive testing.
Can gravity molds make wheels? Sure, suitable for small batches and after-sales parts, with a porosity of about 3%.
Is 50000 module times a hard target? Continuous production is recommended, and intermittent production of 30000 molds is sufficient.
Can CAE simulation save on trial mold costs? Usually, reducing 1 to 2 trial molds saves about 8% of development costs.
Moldes para fundição por baixa pressão (LPDC)
Moldes para fundição por gravidade
Moldes para fundição por contrapressão (CPC)
Moldes para fundição de peças estruturais
Molde para fundição de cubos de roda de motocicleta
Molde para fundição por pressão diferencial de cubos de roda
Molde para fundição por gravidade de cubos de roda
Molde para fundição por baixa pressão de cubos de roda
MOLDES PARA JANTES AUTOMÓVEIS
PEÇAS ESTRUTURAIS AUTOMÓVEIS
OUTROS COMPONENTES DE FUNDIDOS DE ALUMÍNIO
PERFIL DA EMPRESA
ESTRUTURA ORGANIZACIONAL
HISTÓRICO DE DESENVOLVIMENTO
PROPRIEDADE INTELECTUAL
ESPÍRITO DE EQUIPA PARCEIRO
Copyright © Zhejiang Xinfeng Machinery Co., Ltd. All Rights Reserved.